#define BOARD_LORA32_V1_0 0x39
#define BOARD_HELTEC32_V2 0x38
#define BOARD_HELTEC32_V3 0x3A
+ #define BOARD_TDECK 0x3B
#define BOARD_RNODE_NG_20 0x40
#define BOARD_RNODE_NG_21 0x41
#define BOARD_RNODE_NG_22 0x42
#endif
#endif
+ #elif BOARD_MODEL == BOARD_TDECK
+ #define IS_ESP32S3 true
+ #define MODEM SX1262
+ #define DIO2_AS_RF_SWITCH true
+ #define HAS_BUSY true
+ #define HAS_TCXO true
+
+ #define HAS_DISPLAY false
+ #define HAS_CONSOLE false
+ #define HAS_BLUETOOTH false
+ #define HAS_BLE true
+ #define HAS_PMU true
+ #define HAS_NP false
+ #define HAS_SD false
+ #define HAS_EEPROM true
+
+ #define HAS_INPUT true
+ #define HAS_SLEEP true
+ #define PIN_WAKEUP GPIO_NUM_0
+ #define WAKEUP_LEVEL 0
+
+ const int pin_poweron = 10;
+ const int pin_btn_usr1 = 0;
+
+ const int pin_cs = 9;
+ const int pin_reset = 17;
+ const int pin_sclk = 40;
+ const int pin_mosi = 41;
+ const int pin_miso = 38;
+ const int pin_tcxo_enable = -1;
+ const int pin_dio = 45;
+ const int pin_busy = 13;
+
+ const int SD_MISO = 38;
+ const int SD_MOSI = 41;
+ const int SD_CLK = 40;
+ const int SD_CS = 39;
+ const int DISPLAY_CS = 12;
+
+ #if HAS_NP == false
+ #if defined(EXTERNAL_LEDS)
+ const int pin_led_rx = 43;
+ const int pin_led_tx = 43;
+ #else
+ const int pin_led_rx = 43;
+ const int pin_led_tx = 43;
+ #endif
+ #endif
+
#else
#error An unsupported ESP32 board was selected. Cannot compile RNode firmware.
#endif
firmware-t3s3:
arduino-cli compile --log --fqbn "esp32:esp32:esp32s3:CDCOnBoot=cdc" -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x42\""
+firmware-tdeck:
+ arduino-cli compile --log --fqbn "esp32:esp32:esp32s3:CDCOnBoot=cdc" -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x3B\""
+
firmware-lora32_v10: check_bt_buffers
arduino-cli compile --log --fqbn esp32:esp32:ttgo-lora32 -e --build-property "build.partitions=no_ota" --build-property "upload.maximum_size=2097152" --build-property "compiler.cpp.extra_flags=\"-DBOARD_MODEL=0x39\""
@sleep 3
python ./Release/esptool/esptool.py --chip esp32-s3 --port /dev/ttyUSB0 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
+upload-tdeck:
+ arduino-cli upload -p /dev/ttyACM0 --fqbn esp32:esp32:esp32s3
+ @sleep 1
+ rnodeconf /dev/ttyACM0 --firmware-hash $$(./partition_hashes ./build/esp32.esp32.esp32s3/RNode_Firmware.ino.bin)
+ @sleep 3
+ python ./Release/esptool/esptool.py --chip esp32-s3 --port /dev/ttyACM0 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
+
upload-rnode_ng_20:
arduino-cli upload -p /dev/ttyUSB0 --fqbn esp32:esp32:ttgo-lora32
@sleep 1
bool bat_voltage_dropping = false;
float bat_delay_v = 0;
float bat_state_change_v = 0;
+#elif BOARD_MODEL == BOARD_TDECK
+ #define BAT_V_MIN 3.15
+ #define BAT_V_MAX 4.3
+ #define BAT_V_CHG 4.48
+ #define BAT_V_FLOAT 4.33
+ #define BAT_SAMPLES 5
+ const uint8_t pin_vbat = 4;
+ float bat_p_samples[BAT_SAMPLES];
+ float bat_v_samples[BAT_SAMPLES];
+ uint8_t bat_samples_count = 0;
+ int bat_discharging_samples = 0;
+ int bat_charging_samples = 0;
+ int bat_charged_samples = 0;
+ bool bat_voltage_dropping = false;
+ float bat_delay_v = 0;
+ float bat_state_change_v = 0;
#elif BOARD_MODEL == BOARD_HELTEC32_V3
#define BAT_V_MIN 3.15
#define BAT_V_MAX 4.3
void kiss_indicate_battery();
void measure_battery() {
- #if BOARD_MODEL == BOARD_RNODE_NG_21 || BOARD_MODEL == BOARD_LORA32_V2_1 || BOARD_MODEL == BOARD_HELTEC32_V3
+ #if BOARD_MODEL == BOARD_RNODE_NG_21 || BOARD_MODEL == BOARD_LORA32_V2_1 || BOARD_MODEL == BOARD_HELTEC32_V3 || BOARD_MODEL == BOARD_TDECK
battery_installed = true;
battery_indeterminate = true;
}
bool init_pmu() {
- #if BOARD_MODEL == BOARD_RNODE_NG_21 || BOARD_MODEL == BOARD_LORA32_V2_1
+ #if BOARD_MODEL == BOARD_RNODE_NG_21 || BOARD_MODEL == BOARD_LORA32_V2_1 || BOARD_MODEL == BOARD_TDECK
pinMode(pin_vbat, INPUT);
return true;
#elif BOARD_MODEL == BOARD_HELTEC32_V3
boot_seq();
EEPROM.begin(EEPROM_SIZE);
Serial.setRxBufferSize(CONFIG_UART_BUFFER_SIZE);
+
+ #if BOARD_MODEL == BOARD_TDECK
+ pinMode(pin_poweron, OUTPUT);
+ digitalWrite(pin_poweron, HIGH);
+
+ pinMode(SD_CS, OUTPUT);
+ pinMode(DISPLAY_CS, OUTPUT);
+ digitalWrite(SD_CS, HIGH);
+ digitalWrite(DISPLAY_CS, HIGH);
+ #endif
#endif
#if MCU_VARIANT == MCU_NRF52
#endif
} else {
hw_ready = false;
- Serial.write("No valid radio module found\r\n");
+ Serial.write("No radio module found\r\n");
#if HAS_DISPLAY
if (disp_ready) {
device_init_done = true;
}
} else {
hw_ready = false;
+ // Serial.write("Invalid EEPROM configuration\r\n");
#if HAS_DISPLAY
if (disp_ready) {
device_init_done = true;
}
} else {
hw_ready = false;
+ // Serial.write("Device unprovisioned, no device configuration found in EEPROM\r\n");
#if HAS_DISPLAY
if (disp_ready) {
device_init_done = true;
#define CHECKSUMMED_SIZE 0x0B
- #define PRODUCT_RNODE 0x03
- #define PRODUCT_HMBRW 0xF0
- #define PRODUCT_TBEAM 0xE0
- #define PRODUCT_T32_10 0xB2
- #define PRODUCT_T32_20 0xB0
- #define PRODUCT_T32_21 0xB1
- #define PRODUCT_H32_V2 0xC0
- #define PRODUCT_H32_V3 0xC1
- #define PRODUCT_RAK4631 0x10
- #define MODEL_11 0x11
- #define MODEL_12 0x12
- #define MODEL_A1 0xA1
- #define MODEL_A6 0xA6
- #define MODEL_A4 0xA4
- #define MODEL_A9 0xA9
- #define MODEL_A3 0xA3
- #define MODEL_A8 0xA8
- #define MODEL_A2 0xA2
- #define MODEL_A7 0xA7
- #define MODEL_B3 0xB3
- #define MODEL_B8 0xB8
- #define MODEL_B4 0xB4
- #define MODEL_B9 0xB9
- #define MODEL_BA 0xBA
- #define MODEL_BB 0xBB
- #define MODEL_C4 0xC4
- #define MODEL_C9 0xC9
- #define MODEL_C5 0xC5
- #define MODEL_CA 0xCA
- #define MODEL_E4 0xE4
- #define MODEL_E9 0xE9
- #define MODEL_E3 0xE3
- #define MODEL_E8 0xE8
- #define MODEL_FE 0xFE
- #define MODEL_FF 0xFF
+ #define PRODUCT_RNODE 0x03 // Board code 0x31
+ #define MODEL_A4 0xA4 // RNode v1.0, 433 MHz
+ #define MODEL_A9 0xA9 // RNode v1.0, 868 MHz
+
+ // Board code 0x40
+ #define MODEL_A3 0xA3 // RNode v2.0, 433 MHz
+ #define MODEL_A8 0xA8 // RNode v2.0, 868 MHz
+
+ // Board code 0x41
+ #define MODEL_A2 0xA2 // RNode v2.1, 433 MHz
+ #define MODEL_A7 0xA7 // RNode v2.1, 868 MHz
+
+ // Board code 0x42
+ #define MODEL_A1 0xA1 // RNode v2.2, 433 MHz
+ #define MODEL_A6 0xA6 // RNode v2.2, 868 MHz
+
+ #define PRODUCT_TBEAM 0xE0 // Board code 0x33
+ #define MODEL_E4 0xE4 // T-Beam SX1278, 433 Mhz
+ #define MODEL_E9 0xE9 // T-Beam SX1276, 868 Mhz
+ #define MODEL_E3 0xE3 // T-Beam SX1268, 433 Mhz
+ #define MODEL_E8 0xE8 // T-Beam SX1262, 868 Mhz
+
+ #define PRODUCT_TDECK_V1 0xD0 // Board code 0x3B
+ #define MODEL_D4 0xD4 // LilyGO T-Deck, 433 MHz
+ #define MODEL_D9 0xD9 // LilyGO T-Deck, 868 MHz
+
+ #define PRODUCT_T32_10 0xB2 // Board code 0x39
+ #define MODEL_BA 0xBA // LilyGO T3 v1.0, 433 MHz
+ #define MODEL_BB 0xBB // LilyGO T3 v1.0, 868 MHz
+
+ #define PRODUCT_T32_20 0xB0 // Board code 0x36
+ #define MODEL_B3 0xB3 // LilyGO T3 v2.0, 433 MHz
+ #define MODEL_B8 0xB8 // LilyGO T3 v2.0, 868 MHz
+
+ #define PRODUCT_T32_21 0xB1 // Board code 0x37
+ #define MODEL_B4 0xB4 // LilyGO T3 v2.1, 433 MHz
+ #define MODEL_B9 0xB9 // LilyGO T3 v2.1, 868 MHz
+
+ #define PRODUCT_H32_V2 0xC0 // Board code 0x38
+ #define MODEL_C4 0xC4 // Heltec Lora32 v2, 433 MHz
+ #define MODEL_C9 0xC9 // Heltec Lora32 v2, 868 MHz
+
+ #define PRODUCT_H32_V3 0xC1 // Board code 0x3A
+ #define MODEL_C5 0xC5 // Heltec Lora32 v3, 433 MHz
+ #define MODEL_CA 0xCA // Heltec Lora32 v3, 868 MHz
+
+ #define PRODUCT_RAK4631 0x10 // Board code 0x51
+ #define MODEL_11 0x11 // RAK4631, 433 Mhz
+ #define MODEL_12 0x12 // RAK4631, 868 Mhz
+
+ #define PRODUCT_HMBRW 0xF0 // Board code 0x32
+ #define MODEL_FE 0xFE // Homebrew board, max 17dBm output power
+ #define MODEL_FF 0xFF // Homebrew board, max 14dBm output power
+
#define ADDR_PRODUCT 0x00
#define ADDR_MODEL 0x01
void led_rx_off() { digitalWrite(pin_led_rx, LOW); }
void led_tx_on() { digitalWrite(pin_led_tx, LOW); }
void led_tx_off() { digitalWrite(pin_led_tx, HIGH); }
+ #elif BOARD_MODEL == BOARD_TDECK
+ void led_rx_on() { }
+ void led_rx_off() { }
+ void led_tx_on() { }
+ void led_tx_off() { }
#elif BOARD_MODEL == BOARD_LORA32_V1_0
#if defined(EXTERNAL_LEDS)
void led_rx_on() { digitalWrite(pin_led_rx, HIGH); }
if (model == MODEL_C4) LoRa->setTxPower(lora_txp, PA_OUTPUT_PA_BOOST_PIN);
if (model == MODEL_C9) LoRa->setTxPower(lora_txp, PA_OUTPUT_PA_BOOST_PIN);
+ if (model == MODEL_D4) LoRa->setTxPower(lora_txp, PA_OUTPUT_PA_BOOST_PIN);
+ if (model == MODEL_D9) LoRa->setTxPower(lora_txp, PA_OUTPUT_PA_BOOST_PIN);
+
if (model == MODEL_E4) LoRa->setTxPower(lora_txp, PA_OUTPUT_PA_BOOST_PIN);
if (model == MODEL_E9) LoRa->setTxPower(lora_txp, PA_OUTPUT_PA_BOOST_PIN);
if (model == MODEL_E3) LoRa->setTxPower(lora_txp, PA_OUTPUT_PA_BOOST_PIN);
#if PLATFORM == PLATFORM_AVR
if (rval == PRODUCT_RNODE || rval == PRODUCT_HMBRW) {
#elif PLATFORM == PLATFORM_ESP32
- if (rval == PRODUCT_RNODE || rval == BOARD_RNODE_NG_20 || rval == BOARD_RNODE_NG_21 || rval == PRODUCT_HMBRW || rval == PRODUCT_TBEAM || rval == PRODUCT_T32_10 || rval == PRODUCT_T32_20 || rval == PRODUCT_T32_21 || rval == PRODUCT_H32_V2 || rval == PRODUCT_H32_V3) {
+ if (rval == PRODUCT_RNODE || rval == BOARD_RNODE_NG_20 || rval == BOARD_RNODE_NG_21 || rval == PRODUCT_HMBRW || rval == PRODUCT_TBEAM || rval == PRODUCT_T32_10 || rval == PRODUCT_T32_20 || rval == PRODUCT_T32_21 || rval == PRODUCT_H32_V2 || rval == PRODUCT_H32_V3 || rval == PRODUCT_TDECK_V1) {
#elif PLATFORM == PLATFORM_NRF52
if (rval == PRODUCT_RAK4631 || rval == PRODUCT_HMBRW) {
#else
if (model == MODEL_FF || model == MODEL_FE) {
#elif BOARD_MODEL == BOARD_TBEAM
if (model == MODEL_E4 || model == MODEL_E9 || model == MODEL_E3 || model == MODEL_E8) {
+ #elif BOARD_MODEL == BOARD_TDECK
+ if (model == MODEL_D4 || model == MODEL_D9) {
#elif BOARD_MODEL == BOARD_LORA32_V1_0
if (model == MODEL_BA || model == MODEL_BB) {
#elif BOARD_MODEL == BOARD_LORA32_V2_0
pinMode(_ss, OUTPUT);
digitalWrite(_ss, HIGH);
- #if BOARD_MODEL == BOARD_RNODE_NG_22 || BOARD_MODEL == BOARD_HELTEC32_V3
+ #if BOARD_MODEL == BOARD_RNODE_NG_22 || BOARD_MODEL == BOARD_HELTEC32_V3 || BOARD_MODEL == BOARD_TDECK
SPI.begin(pin_sclk, pin_miso, pin_mosi, pin_cs);
#else
SPI.begin();
uint8_t buf[4] = {MODE_TCXO_3_3V_6X, 0x00, 0x00, 0xFF};
#elif BOARD_MODEL == BOARD_TBEAM
uint8_t buf[4] = {MODE_TCXO_1_8V_6X, 0x00, 0x00, 0xFF};
+ #elif BOARD_MODEL == BOARD_TDECK
+ uint8_t buf[4] = {MODE_TCXO_1_8V_6X, 0x00, 0x00, 0xFF};
#elif BOARD_MODEL == BOARD_RNODE_NG_22
uint8_t buf[4] = {MODE_TCXO_1_8V_6X, 0x00, 0x00, 0xFF};
#endif
projects / lora-radio.git / commitdiff