Add BLE driver for NRF52

diff --git a/Bluetooth.h b/Bluetooth.h
index f28f02c0c44349c6a978b183c5c2558660243739..e7231a12d5493ed487fab313a1a6eddd248fe55c 100644 (file)
--- a/Bluetooth.h
+++ b/Bluetooth.h
@@ -13,11 +13,24 @@
 // You should have received a copy of the GNU General Public License
 // along with this program.  If not, see <https://www.gnu.org/licenses/>.
 
+#if MCU_VARIANT == MCU_ESP32
 #include "BluetoothSerial.h"
 #include "esp_bt_main.h"
 #include "esp_bt_device.h"
 
+#elif MCU_VARIANT == MCU_NRF52
+#include <bluefruit.h>
+#include <math.h>
+#endif
+
+#if MCU_VARIANT == MCU_ESP32
 BluetoothSerial SerialBT;
+#elif MCU_VARIANT == MCU_NRF52
+BLEUart SerialBT;
+BLEDis  bledis;
+BLEBas  blebas;
+#endif
+
 #define BT_PAIRING_TIMEOUT 35000
 uint32_t bt_pairing_started = 0;
 
@@ -138,4 +151,145 @@ char bt_devname[11];
     }
   }
 
+#elif MCU_VARIANT == MCU_NRF52
+uint8_t eeprom_read(uint32_t mapped_addr);
+
+void bt_stop() {
+  if (bt_state != BT_STATE_OFF) {
+    bt_allow_pairing = false;
+    bt_state = BT_STATE_OFF;
+  }
+}
+
+void bt_disable_pairing() {
+  bt_allow_pairing = false;
+  bt_ssp_pin = 0;
+  bt_state = BT_STATE_ON;
+}
+
+void bt_pairing_complete(uint16_t conn_handle, uint8_t auth_status) {
+    if (auth_status == BLE_GAP_SEC_STATUS_SUCCESS) {
+      bt_disable_pairing();
+    } else {
+      bt_ssp_pin = 0;
+    }
+}
+
+bool bt_passkey_callback(uint16_t conn_handle, uint8_t const passkey[6], bool match_request) {
+    for (int i = 0; i < 6; i++) {
+        // multiply by tens however many times needed to make numbers appear in order
+        bt_ssp_pin += ((int)passkey[i] - 48) * pow(10, 5-i);
+    }
+    kiss_indicate_btpin();
+    if (match_request) {
+        if (bt_allow_pairing) {
+            return true;
+        }
+    }
+    return false;
+}
+
+void bt_connect_callback(uint16_t conn_handle) {
+    bt_state = BT_STATE_CONNECTED;
+    cable_state = CABLE_STATE_DISCONNECTED;
+}
+
+void bt_disconnect_callback(uint16_t conn_handle, uint8_t reason) {
+    bt_state = BT_STATE_ON;
+}
+
+bool bt_setup_hw() {
+  if (!bt_ready) {
+    #if HAS_EEPROM 
+        if (EEPROM.read(eeprom_addr(ADDR_CONF_BT)) == BT_ENABLE_BYTE) {
+    #else
+        if (eeprom_read(eeprom_addr(ADDR_CONF_BT)) == BT_ENABLE_BYTE) {
+    #endif
+      bt_enabled = true;
+    } else {
+      bt_enabled = false;
+    }
+    Bluefruit.configPrphBandwidth(BANDWIDTH_MAX);
+    Bluefruit.autoConnLed(false);
+    if (Bluefruit.begin()) {
+      Bluefruit.setTxPower(4);    // Check bluefruit.h for supported values
+      Bluefruit.Security.setIOCaps(true, true, false);
+      Bluefruit.Security.setPairPasskeyCallback(bt_passkey_callback);
+      Bluefruit.Periph.setConnectCallback(bt_connect_callback);
+      Bluefruit.Periph.setDisconnectCallback(bt_disconnect_callback);
+      Bluefruit.Security.setIOCaps(true, true, false);
+      Bluefruit.Security.setPairCompleteCallback(bt_pairing_complete);
+      const ble_gap_addr_t gap_addr = Bluefruit.getAddr();
+      char *data = (char*)malloc(BT_DEV_ADDR_LEN+1);
+      for (int i = 0; i < BT_DEV_ADDR_LEN; i++) {
+          data[i] = gap_addr.addr[i];
+      }
+      #if HAS_EEPROM 
+          data[BT_DEV_ADDR_LEN] = EEPROM.read(eeprom_addr(ADDR_SIGNATURE));
+      #else
+          data[BT_DEV_ADDR_LEN] = eeprom_read(eeprom_addr(ADDR_SIGNATURE));
+      #endif
+      unsigned char *hash = MD5::make_hash(data, BT_DEV_ADDR_LEN);
+      memcpy(bt_dh, hash, BT_DEV_HASH_LEN);
+      sprintf(bt_devname, "RNode %02X%02X", bt_dh[14], bt_dh[15]);
+      free(data);
+
+      bt_ready = true;
+      return true;
+
+    } else { return false; }
+  } else { return false; }
+}
+
+void bt_start() {
+  if (bt_state == BT_STATE_OFF) {
+    Bluefruit.setName(bt_devname);
+    bledis.setManufacturer("Adafruit Industries");
+    bledis.setModel("Bluefruit Feather52");
+    // start device information service
+    bledis.begin();
+
+    SerialBT.begin();
+
+    blebas.begin();
+
+    // non-connectable advertising
+    Bluefruit.Advertising.addFlags(BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE);
+    Bluefruit.Advertising.addTxPower();
+
+    // Include bleuart 128-bit uuid
+    Bluefruit.Advertising.addService(SerialBT);
+
+    // There is no room for Name in Advertising packet
+    // Use Scan response for Name
+    Bluefruit.ScanResponse.addName();
+
+    Bluefruit.Advertising.start(0);
+
+    bt_state = BT_STATE_ON;
+   }
+}
+
+bool bt_init() {
+    bt_state = BT_STATE_OFF;
+    if (bt_setup_hw()) {
+      if (bt_enabled && !console_active) bt_start();
+      return true;
+    } else {
+      return false;
+    }
+}
+
+void bt_enable_pairing() {
+  if (bt_state == BT_STATE_OFF) bt_start();
+  bt_allow_pairing = true;
+  bt_pairing_started = millis();
+  bt_state = BT_STATE_PAIRING;
+}
+
+void update_bt() {
+  if (bt_allow_pairing && millis()-bt_pairing_started >= BT_PAIRING_TIMEOUT) {
+    bt_disable_pairing();
+  }
+}
 #endif

diff --git a/Config.h b/Config.h
index 5827e7db9f60305297b76d0406adbb50d5d892c1..82bc783b9fbd8b6b1ff8fa2199ee8c92976a9c5f 100644 (file)
--- a/Config.h
+++ b/Config.h
@@ -304,7 +304,7 @@
         #if BOARD_MODEL == BOARD_RAK4630
             #define HAS_EEPROM false
             #define HAS_DISPLAY false // set for debugging
-            #define HAS_BLUETOOTH false
+            #define HAS_BLUETOOTH true
             #define HAS_CONSOLE false
             #define HAS_PMU false
             #define HAS_NP false

diff --git a/RNode_Firmware.ino b/RNode_Firmware.ino
index ce1d2ef7a8b6e58dc55a66f68562665dcb372f52..d36be3b10d150d78c45322654ab2b5b7c261b1e3 100644 (file)
--- a/RNode_Firmware.ino
+++ b/RNode_Firmware.ino
@@ -140,7 +140,7 @@ void setup() {
     update_display();
   #endif
 
-  #if MCU_VARIANT == MCU_ESP32
+  #if MCU_VARIANT == MCU_ESP32 || MCU_VARIANT == MCU_NRF52
     #if HAS_PMU == true
       pmu_ready = init_pmu();
     #endif

diff --git a/Utilities.h b/Utilities.h
index d6cfdc9b3370675fda1686020d4b31995045de9d..44a5e7850ece96b741abc5f357f3d625bb33f74f 100644 (file)
--- a/Utilities.h
+++ b/Utilities.h
@@ -1207,8 +1207,16 @@ void eeprom_update(int mapped_addr, uint8_t byte) {
             written_bytes = 0;
         }
        #endif
+}
 
+#if !HAS_EEPROM && MCU_VARIANT == MCU_NRF52
+void eeprom_flush() {
+    // sync file contents to flash
+    file.close();
+    file.open(EEPROM_FILE, FILE_O_WRITE);
+    written_bytes = 0;
 }
+#endif
 
 void eeprom_write(uint8_t addr, uint8_t byte) {
        if (!eeprom_info_locked() && addr >= 0 && addr < EEPROM_RESERVED) {
@@ -1344,8 +1352,16 @@ bool eeprom_checksum_valid() {
 void bt_conf_save(bool is_enabled) {
        if (is_enabled) {
                eeprom_update(eeprom_addr(ADDR_CONF_BT), BT_ENABLE_BYTE);
+        #if !HAS_EEPROM && MCU_VARIANT == MCU_NRF52
+            // have to do a flush because we're only writing 1 byte and it syncs after 8
+            eeprom_flush();
+        #endif
        } else {
                eeprom_update(eeprom_addr(ADDR_CONF_BT), 0x00);
+        #if !HAS_EEPROM && MCU_VARIANT == MCU_NRF52
+            // have to do a flush because we're only writing 1 byte and it syncs after 8
+            eeprom_flush();
+        #endif
        }
 }