#define INTERFACE_COUNT 1
const int pin_led_rx = 14;
const int pin_led_tx = 32;
- const uint8_t interfaces[INTERFACE_COUNT] = {SX127X};
+ const uint8_t interfaces[INTERFACE_COUNT] = {SX1276};
const bool interface_cfg[INTERFACE_COUNT][3] = {
// SX127X
{
const int pin_led_tx = 4;
#if BOARD_VARIANT == MODEL_E4 || BOARD_VARIANT == MODEL_E9
- const uint8_t interfaces[INTERFACE_COUNT] = {SX127X};
+ const uint8_t interfaces[INTERFACE_COUNT] = {SX1276};
const bool interface_cfg[INTERFACE_COUNT][3] = {
// SX127X
{
const int pin_led_rx = 14;
const int pin_led_tx = 32;
- const uint8_t interfaces[INTERFACE_COUNT] = {SX127X};
+ const uint8_t interfaces[INTERFACE_COUNT] = {SX1276};
const bool interface_cfg[INTERFACE_COUNT][3] = {
// SX127X
{
},
};
const int8_t interface_pins[INTERFACE_COUNT][10] = {
- // SX1262
+ // SX127X
{
4, // pin_ss
-1, // pin_sclk
#endif
- const uint8_t interfaces[INTERFACE_COUNT] = {SX127X};
+ const uint8_t interfaces[INTERFACE_COUNT] = {SX1276};
const bool interface_cfg[INTERFACE_COUNT][3] = {
// SX127X
{
const int pin_led_tx = 25;
#endif
- const uint8_t interfaces[INTERFACE_COUNT] = {SX127X};
+ const uint8_t interfaces[INTERFACE_COUNT] = {SX1276};
const bool interface_cfg[INTERFACE_COUNT][3] = {
// SX127X
{
#endif
#endif
- const uint8_t interfaces[INTERFACE_COUNT] = {SX127X};
+ const uint8_t interfaces[INTERFACE_COUNT] = {SX1276};
const bool interface_cfg[INTERFACE_COUNT][3] = {
// SX127X
{
}
};
- // todo ce-ise all boards below here
-
#elif BOARD_MODEL == BOARD_T3S3
#define IS_ESP32S3 true
#define HAS_DISPLAY true
#define INTERFACE_COUNT 1
const int pin_btn_usr1 = 0;
- #if BOARD_VARIANT == MODEL_A1
+ #if BOARD_VARIANT == MODEL_A1 || BOARD_VARIANT == MODEL_A6
const uint8_t interfaces[INTERFACE_COUNT] = {SX1262};
const bool interface_cfg[INTERFACE_COUNT][3] = {
// SX1262
-1 // pin_tcxo_enable
}
};
+ #elif BOARD_VARIANT == MODEL_A5 || BOARD_VARIANT == MODEL_AA
+ const uint8_t interfaces[INTERFACE_COUNT] = {SX1278};
+ const bool interface_cfg[INTERFACE_COUNT][3] = {
+ // SX1278
+ {
+ false, // DEFAULT_SPI
+ false, // HAS_TCXO
+ false // DIO2_AS_RF_SWITCH
+ },
+ };
+ const uint8_t interface_pins[INTERFACE_COUNT][10] = {
+ // SX1278
+ {
+ 7, // pin_ss
+ 5, // pin_sclk
+ 6, // pin_mosi
+ 3, // pin_miso
+ 34, // pin_busy
+ 33, // pin_dio
+ 8, // pin_reset
+ -1, // pin_txen
+ -1, // pin_rxen
+ -1 // pin_tcxo_enable
+ }
+ };
#elif BOARD_VARIANT == MODEL_AC // SX1280 with PA
#define CONFIG_QUEUE_0_SIZE 6144
const uint8_t interfaces[INTERFACE_COUNT] = {SX1280};
#elif BOARD_MODEL == BOARD_TDECK
#define IS_ESP32S3 true
- #define MODEM SX1262
- #define DIO2_AS_RF_SWITCH true
- #define HAS_BUSY true
- #define HAS_TCXO true
-
#define HAS_DISPLAY false
+ #define HAS_CONSOLE false
+ #define HAS_BLUETOOTH false
+ #define HAS_BLE true
+ #define HAS_PMU true
+ #define HAS_NP false
+ #define HAS_SD false
+ #define HAS_EEPROM true
+
+ #define HAS_INPUT true
+ #define HAS_SLEEP true
+ #define PIN_WAKEUP GPIO_NUM_0
+ #define WAKEUP_LEVEL 0
const int pin_poweron = 10;
const int pin_btn_usr1 = 0;
-
- const int pin_cs = 9;
- const int pin_reset = 17;
- const int pin_sclk = 40;
- const int pin_mosi = 41;
- const int pin_miso = 38;
- const int pin_tcxo_enable = -1;
- const int pin_dio = 45;
- const int pin_busy = 13;
const int SD_MISO = 38;
const int SD_MOSI = 41;
const int DISPLAY_CLK = 40;
const int DISPLAY_BL_PIN = 42;
+ #define INTERFACE_COUNT 1
+
+ const uint8_t interfaces[INTERFACE_COUNT] = {SX1262};
+ const bool interface_cfg[INTERFACE_COUNT][3] = {
+ // SX1262
+ {
+ false, // DEFAULT_SPI
+ true, // HAS_TCXO
+ true // DIO2_AS_RF_SWITCH
+ },
+ };
+ const uint8_t interface_pins[INTERFACE_COUNT][10] = {
+ // SX1262
+ {
+ 9, // pin_ss
+ 40, // pin_sclk
+ 41, // pin_mosi
+ 38, // pin_miso
+ 13, // pin_busy
+ 45, // pin_dio
+ 17, // pin_reset
+ -1, // pin_txen
+ -1, // pin_rxen
+ -1 // pin_tcxo_enable
+ }
+ };
+
#if HAS_NP == false
#if defined(EXTERNAL_LEDS)
const int pin_led_rx = 43;
#elif BOARD_MODEL == BOARD_TBEAM_S_V1
#define IS_ESP32S3 true
- #define MODEM SX1262
- #define DIO2_AS_RF_SWITCH true
- #define HAS_BUSY true
- #define HAS_TCXO true
#define OCP_TUNED 0x38
#define HAS_DISPLAY true
+ #define DISPLAY MONO_OLED
#define HAS_CONSOLE true
#define HAS_BLUETOOTH false
#define HAS_BLE true
#define I2C_SDA 42
const int pin_btn_usr1 = 0;
-
- const int pin_cs = 10;
- const int pin_reset = 5;
- const int pin_sclk = 12;
- const int pin_mosi = 11;
- const int pin_miso = 13;
- const int pin_tcxo_enable = -1;
- const int pin_dio = 1;
- const int pin_busy = 4;
const int SD_MISO = 37;
const int SD_MOSI = 35;
const int IMU_CS = 34;
- #if HAS_NP == false
- #if defined(EXTERNAL_LEDS)
- const int pin_led_rx = 43;
- const int pin_led_tx = 43;
- #else
- const int pin_led_rx = 43;
- const int pin_led_tx = 43;
- #endif
- #endif
+ #define INTERFACE_COUNT 1
- #if BOARD_VARIANT == MODEL_A1
const uint8_t interfaces[INTERFACE_COUNT] = {SX1262};
const bool interface_cfg[INTERFACE_COUNT][3] = {
// SX1262
const uint8_t interface_pins[INTERFACE_COUNT][10] = {
// SX1262
{
- 7, // pin_ss
- 5, // pin_sclk
- 6, // pin_mosi
- 3, // pin_miso
- 34, // pin_busy
- 33, // pin_dio
- 8, // pin_reset
+ 10, // pin_ss
+ 12, // pin_sclk
+ 11, // pin_mosi
+ 13, // pin_miso
+ 4, // pin_busy
+ 1, // pin_dio
+ 5, // pin_reset
-1, // pin_txen
-1, // pin_rxen
-1 // pin_tcxo_enable
}
};
- #elif BOARD_VARIANT == MODEL_AC // SX1280 with PA
- #define CONFIG_UART_BUFFER_SIZE 40000
- #define CONFIG_QUEUE_0_SIZE 40000
- const uint8_t interfaces[INTERFACE_COUNT] = {SX1280};
- const bool interface_cfg[INTERFACE_COUNT][3] = {
- // SX1280
- {
- false, // DEFAULT_SPI
- false, // HAS_TCXO
- false // DIO2_AS_RF_SWITCH
- },
- };
- const uint8_t interface_pins[INTERFACE_COUNT][10] = {
- // SX1280
- {
- 7, // pin_ss
- 5, // pin_sclk
- 6, // pin_mosi
- 3, // pin_miso
- 36, // pin_busy
- 9, // pin_dio
- 8, // pin_reset
- 10, // pin_txen
- 21, // pin_rxen
- -1 // pin_tcxo_enable
- }
- };
+
+ #if HAS_NP == false
+ #if defined(EXTERNAL_LEDS)
+ const int pin_led_rx = 43;
+ const int pin_led_tx = 43;
+ #else
+ const int pin_led_rx = 43;
+ const int pin_led_tx = 43;
+ #endif
#endif
#elif BOARD_MODEL == BOARD_E22_ESP32
#define HAS_DISPLAY true
#define DISPLAY OLED
+ // currently there is only support for using one Bluetooth type,
+ // Bluetooth has been chosen over BLE as it is less experimental
#define HAS_BLUETOOTH true
- #define HAS_BLE true
+ //#define HAS_BLE true
#define HAS_CONSOLE true
#define HAS_SD false
#define HAS_EEPROM true
-1 // pin_tcxo_enable
}
};
-
- #elif BOARD_MODEL == BOARD_TDECK
- #define IS_ESP32S3 true
- #define MODEM SX1262
- #define DIO2_AS_RF_SWITCH true
- #define HAS_BUSY true
- #define HAS_TCXO true
-
- #define HAS_DISPLAY false
- #define HAS_CONSOLE false
- #define HAS_BLUETOOTH false
- #define HAS_BLE true
- #define HAS_PMU true
- #define HAS_NP false
- #define HAS_SD false
- #define HAS_EEPROM true
-
- #define HAS_INPUT true
- #define HAS_SLEEP true
- #define PIN_WAKEUP GPIO_NUM_0
- #define WAKEUP_LEVEL 0
-
- const int pin_poweron = 10;
- const int pin_btn_usr1 = 0;
-
- const int pin_cs = 9;
- const int pin_reset = 17;
- const int pin_sclk = 40;
- const int pin_mosi = 41;
- const int pin_miso = 38;
- const int pin_tcxo_enable = -1;
- const int pin_dio = 45;
- const int pin_busy = 13;
-
- const int SD_MISO = 38;
- const int SD_MOSI = 41;
- const int SD_CLK = 40;
- const int SD_CS = 39;
-
- const int DISPLAY_DC = 11;
- const int DISPLAY_CS = 12;
- const int DISPLAY_MISO = 38;
- const int DISPLAY_MOSI = 41;
- const int DISPLAY_CLK = 40;
- const int DISPLAY_BL_PIN = 42;
-
- #if HAS_NP == false
- #if defined(EXTERNAL_LEDS)
- const int pin_led_rx = 43;
- const int pin_led_tx = 43;
- #else
- const int pin_led_rx = 43;
- const int pin_led_tx = 43;
- #endif
- #endif
-
- #elif BOARD_MODEL == BOARD_TBEAM_S_V1
- #define IS_ESP32S3 true
- #define MODEM SX1262
- #define DIO2_AS_RF_SWITCH true
- #define HAS_BUSY true
- #define HAS_TCXO true
-
- #define HAS_DISPLAY true
- #define HAS_CONSOLE true
- #define HAS_BLUETOOTH false
- #define HAS_BLE true
- #define HAS_PMU true
- #define HAS_NP false
- #define HAS_SD false
- #define HAS_EEPROM true
-
- #define HAS_INPUT true
- #define HAS_SLEEP false
-
- #define PMU_IRQ 40
- #define I2C_SCL 41
- #define I2C_SDA 42
-
- const int pin_btn_usr1 = 0;
-
- const int pin_cs = 10;
- const int pin_reset = 5;
- const int pin_sclk = 12;
- const int pin_mosi = 11;
- const int pin_miso = 13;
- const int pin_tcxo_enable = -1;
- const int pin_dio = 1;
- const int pin_busy = 4;
-
- const int SD_MISO = 37;
- const int SD_MOSI = 35;
- const int SD_CLK = 36;
- const int SD_CS = 47;
-
- const int IMU_CS = 34;
-
- #if HAS_NP == false
- #if defined(EXTERNAL_LEDS)
- const int pin_led_rx = 43;
- const int pin_led_tx = 43;
- #else
- const int pin_led_rx = 43;
- const int pin_led_tx = 43;
- #endif
- #endif
- #endif
-
+ #else
+ #error An unsupported ESP32 board was selected. Cannot compile RNode firmware.
+ #endif
#elif MCU_VARIANT == MCU_NRF52
+ #define CONFIG_UART_BUFFER_SIZE 6144
+ #define CONFIG_QUEUE_0_SIZE 6144
+ #define CONFIG_QUEUE_MAX_LENGTH 200
+
#if BOARD_MODEL == BOARD_TECHO
#define _PINNUM(port, pin) ((port) * 32 + (pin))
#define HAS_INPUT true
const int pin_led_rx = LED_BLUE;
const int pin_led_tx = LED_GREEN;
- #elif BOARD_MODEL == BOARD_TECHO
- #define _PINNUM(port, pin) ((port) * 32 + (pin))
- #define MODEM SX1262
- #define HAS_EEPROM false
- #define HAS_BLUETOOTH false
- #define HAS_BLE true
- #define HAS_CONSOLE false
- #define HAS_PMU true
- #define HAS_NP false
- #define HAS_SD false
- #define HAS_TCXO true
- #define HAS_BUSY true
- #define HAS_INPUT true
- #define HAS_SLEEP true
- #define BLE_MANUFACTURER "LilyGO"
- #define BLE_MODEL "T-Echo"
-
- #define HAS_INPUT true
- #define EEPROM_SIZE 296
- #define EEPROM_OFFSET EEPROM_SIZE-EEPROM_RESERVED
-
- #define CONFIG_UART_BUFFER_SIZE 32768
- #define CONFIG_QUEUE_SIZE 6144
- #define CONFIG_QUEUE_MAX_LENGTH 200
-
- #define HAS_DISPLAY true
- #define DISPLAY EINK_BW
- #define HAS_BACKLIGHT true
- #define DISPLAY_SCALE 1
-
- #define LED_ON LOW
- #define LED_OFF HIGH
- #define PIN_LED_GREEN _PINNUM(1, 1)
- #define PIN_LED_RED _PINNUM(1, 3)
- #define PIN_LED_BLUE _PINNUM(0, 14)
- #define PIN_VEXT_EN _PINNUM(0, 12)
-
- const int pin_disp_cs = 30;
- const int pin_disp_dc = 28;
- const int pin_disp_reset = 2;
- const int pin_disp_busy = 3;
- const int pin_disp_en = -1;
- const int pin_disp_sck = 31;
- const int pin_disp_mosi = 29;
- const int pin_disp_miso = -1;
- const int pin_backlight = 43;
-
- const int pin_btn_usr1 = _PINNUM(1, 10);
- const int pin_btn_touch = _PINNUM(0, 11);
-
- const int pin_reset = 25;
- const int pin_cs = 24;
- const int pin_sclk = 19;
- const int pin_mosi = 22;
- const int pin_miso = 23;
- const int pin_busy = 17;
- const int pin_dio = 20;
- const int pin_tcxo_enable = 21;
- const int pin_led_rx = PIN_LED_BLUE;
- const int pin_led_tx = PIN_LED_RED;
-
#elif BOARD_MODEL == BOARD_HELTEC_T114
- #define MODEM SX1262
#define HAS_EEPROM false
#define HAS_DISPLAY true
+ #define DISPLAY TFT
+ #define DISPLAY_SCALE_OVERRIDE true
+ #define DISPLAY_SCALE 2
#define HAS_BLUETOOTH false
#define HAS_BLE true
#define HAS_CONSOLE false
#define NP_M 1
const int pin_np = PIN_T114_LED;
- // SPI
- #define PIN_T114_MOSI 22
- #define PIN_T114_MISO 23
- #define PIN_T114_SCK 19
- #define PIN_T114_SS 24
-
- // SX1262
- #define PIN_T114_RST 25
- #define PIN_T114_DIO1 20
- #define PIN_T114_BUSY 17
-
- // TFT
- #define DISPLAY_SCALE_OVERRIDE true
- #define DISPLAY_SCALE 2
- #define PIN_T114_TFT_MOSI 9
- #define PIN_T114_TFT_MISO 11 // not connected
- #define PIN_T114_TFT_SCK 8
- #define PIN_T114_TFT_SS 11
- #define PIN_T114_TFT_DC 12
- #define PIN_T114_TFT_RST 2
- #define PIN_T114_TFT_EN 3
- #define PIN_T114_TFT_BLGT 15
// pins for buttons on Heltec T114
const int pin_btn_usr1 = 42;
- // pins for sx1262 on Heltec T114
- const int pin_reset = PIN_T114_RST;
- const int pin_cs = PIN_T114_SS;
- const int pin_sclk = PIN_T114_SCK;
- const int pin_mosi = PIN_T114_MOSI;
- const int pin_miso = PIN_T114_MISO;
- const int pin_busy = PIN_T114_BUSY;
- const int pin_dio = PIN_T114_DIO1;
const int pin_led_rx = 35;
const int pin_led_tx = 35;
- const int pin_tcxo_enable = -1;
+
+ #define PIN_T114_TFT_BLGT 15
+ #define PIN_T114_TFT_EN 3
// pins for ST7789 display on Heltec T114
- const int DISPLAY_DC = PIN_T114_TFT_DC;
- const int DISPLAY_CS = PIN_T114_TFT_SS;
- const int DISPLAY_MISO = PIN_T114_TFT_MISO;
- const int DISPLAY_MOSI = PIN_T114_TFT_MOSI;
- const int DISPLAY_CLK = PIN_T114_TFT_SCK;
+ const int DISPLAY_DC = 12;
+ const int DISPLAY_CS = 11;
+ const int DISPLAY_MISO = 11;
+ const int DISPLAY_MOSI = 9;
+ const int DISPLAY_CLK = 8;
const int DISPLAY_BL_PIN = PIN_T114_TFT_BLGT;
- const int DISPLAY_RST = PIN_T114_TFT_RST;
+ const int DISPLAY_RST = 2;
+ #define INTERFACE_COUNT 1
+
+ const uint8_t interfaces[INTERFACE_COUNT] = {SX1262};
+ const bool interface_cfg[INTERFACE_COUNT][3] = {
+ // SX1262
+ {
+ false, // DEFAULT_SPI
+ true, // HAS_TCXO
+ true // DIO2_AS_RF_SWITCH
+ }
+ };
+ const int8_t interface_pins[INTERFACE_COUNT][10] = {
+ // SX1262
+ {
+ 24, // pin_ss
+ 19, // pin_sclk
+ 22, // pin_mosi
+ 23, // pin_miso
+ 17, // pin_busy
+ 20, // pin_dio
+ 25, // pin_reset
+ -1, // pin_txen
+ -1, // pin_rxen
+ -1 // pin_tcxo_enable
+ }
+ };
#else
#error An unsupported nRF board was selected. Cannot compile RNode firmware.
#endif
projects / lora-radio.git / commitdiff