#define ISR_VECT
#endif
+// SX128x registers
#define OP_RF_FREQ_8X 0x86
#define OP_SLEEP_8X 0x84
#define OP_STANDBY_8X 0x80
setTimeout(0);
}
-void ISR_VECT sx128x::onDio0Rise() { sx128x_modem.handleDio0Rise(); }
-void sx128x::handleDio0Rise() {
+bool ISR_VECT sx128x::getPacketValidity() {
uint8_t buf[2];
buf[0] = 0x00;
buf[1] = 0x00;
executeOpcodeRead(OP_GET_IRQ_STATUS_8X, buf, 2);
+
executeOpcode(OP_CLEAR_IRQ_STATUS_8X, buf, 2);
+
if ((buf[1] & IRQ_PAYLOAD_CRC_ERROR_MASK_8X) == 0) {
- // received a packet
- _packetIndex = 0;
+ return true;
+ } else {
+ return false;
+ }
+}
- uint8_t rxbuf[2] = {0};
- executeOpcodeRead(OP_RX_BUFFER_STATUS_8X, rxbuf, 2);
+void ISR_VECT sx128x::onDio0Rise() {
+ BaseType_t int_status = taskENTER_CRITICAL_FROM_ISR();
+ if (sx128x_modem.getPacketValidity()) { sx128x_modem.handleDio0Rise(); }
+ // On the SX1280, there is a bug which can cause the busy line
+ // to remain high if a high amount of packets are received when
+ // in continuous RX mode. This is documented as Errata 16.1 in
+ // the SX1280 datasheet v3.2 (page 149)
+ // Therefore, the modem is set into receive mode each time a packet is received.
+ sx128x_modem.receive();
+ taskEXIT_CRITICAL_FROM_ISR(int_status);
+}
- _rxPacketLength = rxbuf[0];
- _fifo_rx_addr_ptr = rxbuf[1];
- readBuffer(_packet, _rxPacketLength);
+void sx128x::handleDio0Rise() {
+ // received a packet
+ _packetIndex = 0;
- // On the SX1280, there is a bug which can cause the busy line
- // to remain high if a high amount of packets are received when
- // in continuous RX mode. This is documented as Errata 16.1 in
- // the SX1280 datasheet v3.2 (page 149)
- // Therefore, the modem is set into receive mode each time a packet is received.
- receive(0);
+ uint8_t rxbuf[2] = {0};
+ executeOpcodeRead(OP_RX_BUFFER_STATUS_8X, rxbuf, 2);
+
+ // If implicit header mode is enabled, read packet length as payload length instead.
+ // See SX1280 datasheet v3.2, page 92
+ if (_implicitHeaderMode == 0x80) {
+ _rxPacketLength = _payloadLength;
+ } else {
+ _rxPacketLength = rxbuf[0];
+ }
- if (_onReceive) { _onReceive(_rxPacketLength); }
+ if (_onReceive) {
+ _onReceive(_rxPacketLength);
}
}
return response;
}
-void sx128x::rxAntEnable() {
- if (_txen != -1) { digitalWrite(_txen, LOW); }
- if (_rxen != -1) { digitalWrite(_rxen, HIGH); }
+void sx128x::rxAntEnable()
+{
+ if (_txen != -1) {
+ digitalWrite(_txen, LOW);
+ }
+ if (_rxen != -1) {
+ digitalWrite(_rxen, HIGH);
+ }
}
-void sx128x::txAntEnable() {
- if (_txen != -1) { digitalWrite(_txen, HIGH); }
- if (_rxen != -1) { digitalWrite(_rxen, LOW); }
+void sx128x::txAntEnable()
+{
+ if (_txen != -1) {
+ digitalWrite(_txen, HIGH);
+ }
+ if (_rxen != -1) {
+ digitalWrite(_rxen, LOW);
+ }
}
void sx128x::loraMode() {
// because there is no access to these registers on the sx1280, we have
// to set all these parameters at once or not at all.
uint8_t buf[7];
-
// calculate exponent and mantissa values for modem
- // uint8_t e = 1;
- // uint8_t m = 1;
- // uint32_t preamblelen;
-
- // while (e <= 15) {
- // while (m <= 15) {
- // preamblelen = m * (pow(2,e));
- // if (preamblelen >= preamble) break;
- // m++;
- // }
- // if (preamblelen >= preamble) break;
- // m = 0;
- // e++;
- // }
-
- // Serial.printf("Calculated preamble: %d\r\n", preamblelen);
- // Serial.printf("Reg value: %d\r\n", (e << 4) | m);
-
- // TODO: Remove / clean
- //buf[0] = (e << 4) | m;
- buf[0] = 0x1C;
+ uint8_t e = 1;
+ uint8_t m = 1;
+ uint32_t preamblelen;
+
+ while (e <= 15) {
+ while (m <= 15) {
+ preamblelen = m * (pow(2,e));
+ if (preamblelen >= preamble) break;
+ m++;
+ }
+ if (preamblelen >= preamble) break;
+ m = 0;
+ e++;
+ }
+
+ buf[0] = (e << 4) | m;
buf[1] = headermode;
buf[2] = length;
buf[3] = crc;
loraMode();
rxAntEnable();
- setFrequency(_frequency);
+ Serial.printf("Setting freq to %d\r\n", _frequency);
+ Serial.printf("Should be %d\r\n", frequency);
+ setFrequency(frequency);
// set LNA boost
// todo: implement this
return buf[0];
}
-int ISR_VECT sx128x::packetRssi() {
- // may need more calculations here
- uint8_t buf[5] = {0};
- executeOpcodeRead(OP_PACKET_STATUS_8X, buf, 5);
- int pkt_rssi = -buf[0] / 2;
- return pkt_rssi;
-}
-
int ISR_VECT sx128x::packetRssi(uint8_t pkt_snr_raw) {
// may need more calculations here
uint8_t buf[5] = {0};
float ISR_VECT sx128x::packetSnr() {
uint8_t buf[5] = {0};
- executeOpcodeRead(OP_PACKET_STATUS_8X, buf, 3);
+ executeOpcodeRead(OP_PACKET_STATUS_8X, buf, 5);
return float(buf[1]) * 0.25;
}
return size;
}
-int ISR_VECT sx128x::available() { return _rxPacketLength - _packetIndex; }
+int ISR_VECT sx128x::available()
+{
+ return _rxPacketLength - _packetIndex;
+}
int ISR_VECT sx128x::read()
{
- if (!available()) {
- return -1;
- }
+ if (!available()) {
+ return -1;
+ }
+
+ // if received new packet
+ if (_packetIndex == 0) {
+ uint8_t rxbuf[2] = {0};
+ executeOpcodeRead(OP_RX_BUFFER_STATUS_8X, rxbuf, 2);
+ int size;
+ // If implicit header mode is enabled, read packet length as payload length instead.
+ // See SX1280 datasheet v3.2, page 92
+ if (_implicitHeaderMode == 0x80) {
+ size = _payloadLength;
+ } else {
+ size = rxbuf[0];
+ }
+ _fifo_rx_addr_ptr = rxbuf[1];
- uint8_t byte = _packet[_packetIndex];
- _packetIndex++;
- return byte;
+ if (size > 255) {
+ size = 255;
+ }
+
+ readBuffer(_packet, size);
+ }
+
+ uint8_t byte = _packet[_packetIndex];
+ _packetIndex++;
+ return byte;
}
int sx128x::peek()
executeOpcode(OP_SET_IRQ_FLAGS_8X, buf, 8);
#ifdef SPI_HAS_NOTUSINGINTERRUPT
- _spiModem->usingInterrupt(digitalPinToInterrupt(_dio0));
+ SPI.usingInterrupt(digitalPinToInterrupt(_dio0));
#endif
- // extern void onDio0Rise();
attachInterrupt(digitalPinToInterrupt(_dio0), onDio0Rise, RISING);
} else {
rxAntEnable();
- // On the SX1280, there is a bug which can cause the busy line
- // to remain high if a high amount of packets are received when
- // in continuous RX mode. This is documented as Errata 16.1 in
- // the SX1280 datasheet v3.2 (page 149)
- // Therefore, the modem is set to single RX mode below instead.
- uint8_t mode[3] = {0}; // single RX mode
- executeOpcode(OP_RX_8X, mode, 3);
+ // On the SX1280, there is a bug which can cause the busy line
+ // to remain high if a high amount of packets are received when
+ // in continuous RX mode. This is documented as Errata 16.1 in
+ // the SX1280 datasheet v3.2 (page 149)
+ // Therefore, the modem is set to single RX mode below instead.
+ uint8_t mode[3] = {0}; // single RX mode
+ executeOpcode(OP_RX_8X, mode, 3);
}
void sx128x::standby()
void sx128x::setTxPower(int level, int outputPin) {
uint8_t tx_buf[2];
- #if BOARD_VARIANT == MODEL_13
+ #if BOARD_VARIANT == MODEL_13 || BOARD_VARIANT == MODEL_21
// RAK4631 with WisBlock SX1280 module (LIBSYS002)
if (level > 27) {
level = 27;
reg_value = -18;
break;
case 1:
- reg_value = -17;
+ reg_value = -16;
break;
case 2:
- reg_value = -16;
+ reg_value = -15;
break;
case 3:
- reg_value = -15;
+ reg_value = -14;
break;
case 4:
- reg_value = -14;
+ reg_value = -13;
break;
case 5:
- reg_value = -13;
+ reg_value = -12;
break;
case 6:
- reg_value = -12;
+ reg_value = -11;
break;
case 7:
- reg_value = -10;
+ reg_value = -9;
break;
case 8:
- reg_value = -9;
+ reg_value = -8;
break;
case 9:
- reg_value = -8;
+ reg_value = -7;
break;
case 10:
- reg_value = -7;
+ reg_value = -6;
break;
case 11:
- reg_value = -6;
+ reg_value = -5;
break;
case 12:
- reg_value = -5;
+ reg_value = -4;
break;
case 13:
- reg_value = -4;
+ reg_value = -3;
break;
case 14:
- reg_value = -3;
+ reg_value = -2;
break;
case 15:
- reg_value = -2;
+ reg_value = -1;
break;
case 16:
- reg_value = -1;
+ reg_value = 0;
break;
case 17:
- reg_value = 0;
+ reg_value = 1;
break;
case 18:
- reg_value = 1;
+ reg_value = 2;
break;
case 19:
- reg_value = 2;
+ reg_value = 3;
break;
case 20:
- reg_value = 3;
+ reg_value = 4;
break;
case 21:
- reg_value = 4;
+ reg_value = 5;
break;
case 22:
- reg_value = 5;
+ reg_value = 6;
break;
case 23:
- reg_value = 6;
+ reg_value = 7;
break;
case 24:
reg_value = 8;
break;
}
- tx_buf[0] = reg_value;
+ tx_buf[0] = reg_value + 18;
tx_buf[1] = 0xE0; // ramping time - 20 microseconds
executeOpcode(OP_TX_PARAMS_8X, tx_buf, 2);
-
+
+ #elif BOARD_VARIANT == MODEL_AC
// T3S3 SX1280 PA
- #elif BOARD_VARIANT == MODEL_AB
- if (level > 20) { level = 20; }
- else if (level < 0) { level = 0; }
-
- _txp = level;
- int reg_value;
-
- switch (level) {
- /*case 0:
- reg_value = -18;
- break;
- case 1:
- reg_value = -17;
- break;
- case 2:
- reg_value = -16;
- break;
- case 3:
- reg_value = -15;
- break;
- case 4:
- reg_value = -14;
- break;
- case 5:
- reg_value = -13;
- break;
- case 6:
- reg_value = -12;
- break;
- case 7:
- reg_value = -10;
- break;
- case 8:
- reg_value = -9;
- break;
- case 9:
- reg_value = -8;
- break;
- case 10:
- reg_value = -7;
- break;
- case 11:
- reg_value = -6;
- break;
- case 12:
- reg_value = -5;
- break;
- case 13:
- reg_value = -4;
- break;
- case 14:
- reg_value = -3;
- break;
- case 15:
- reg_value = -2;
- break;
- case 16:
- reg_value = -1;
- break;
- case 17:
- reg_value = 0;
- break;
- case 18:
- reg_value = 1;
- break;
- case 19:
- reg_value = 2;
- break;*/
- case 20:
- reg_value = 3;
- break;
- default:
- reg_value = 0;
- break;
- }
+ if (level > 20) { level = 20; }
+ else if (level < 0) { level = 0; }
+
+ _txp = level;
+
+ int reg_value;
+
+ switch (level) {
+ /*case 0:
+ reg_value = -18;
+ break;
+ case 1:
+ reg_value = -17;
+ break;
+ case 2:
+ reg_value = -16;
+ break;
+ case 3:
+ reg_value = -15;
+ break;
+ case 4:
+ reg_value = -14;
+ break;
+ case 5:
+ reg_value = -13;
+ break;
+ case 6:
+ reg_value = -12;
+ break;
+ case 7:
+ reg_value = -10;
+ break;
+ case 8:
+ reg_value = -9;
+ break;
+ case 9:
+ reg_value = -8;
+ break;
+ case 10:
+ reg_value = -7;
+ break;
+ case 11:
+ reg_value = -6;
+ break;
+ case 12:
+ reg_value = -5;
+ break;
+ case 13:
+ reg_value = -4;
+ break;
+ case 14:
+ reg_value = -3;
+ break;
+ case 15:
+ reg_value = -2;
+ break;
+ case 16:
+ reg_value = -1;
+ break;
+ case 17:
+ reg_value = 0;
+ break;
+ case 18:
+ reg_value = 1;
+ break;
+ case 19:
+ reg_value = 2;
+ break;*/
+ case 20:
+ reg_value = 3;
+ break;
+ default:
+ reg_value = 0;
+ break;
+ }
- tx_buf[0] = reg_value;
- tx_buf[1] = 0xE0; // ramping time - 20 microseconds
-
- // For SX1280 boards with no specific PA requirements
+ tx_buf[0] = reg_value;
+ tx_buf[1] = 0xE0; // ramping time - 20 microseconds
#else
- if (level > 13) {
- level = 13;
- } else if (level < -18) {
- level = -18;
- }
+ // For SX1280 boards with no specific PA requirements
+ if (level > 13) {
+ level = 13;
+ } else if (level < -18) {
+ level = -18;
+ }
- _txp = level;
+ _txp = level;
- tx_buf[0] = level;
- tx_buf[1] = 0xE0; // ramping time - 20 microseconds
+ tx_buf[0] = level + 18;
+ tx_buf[1] = 0xE0; // ramping time - 20 microseconds
#endif
executeOpcode(OP_TX_PARAMS_8X, tx_buf, 2);
}
return 0;
}
-// todo: do i need this??
-void sx128x::handleLowDataRate() { }
+void sx128x::handleLowDataRate(){
+ // todo: do i need this??
+}
-// todo: check if there's anything the sx1280 can do here
-void sx128x::optimizeModemSensitivity() { }
+void sx128x::optimizeModemSensitivity(){
+ // todo: check if there's anything the sx1280 can do here
+}
-void sx128x::setSignalBandwidth(uint32_t sbw) {
+void sx128x::setSignalBandwidth(uint32_t sbw)
+{
if (sbw <= 203.125E3) {
_bw = 0x34;
} else if (sbw <= 406.25E3) {
setModulationParams(_sf, _bw, _cr);
}
-uint8_t sx128x::getCodingRate4() { return _cr + 4; }
+uint8_t sx128x::getCodingRate4()
+{
+ return _cr + 4;
+}
-void sx128x::setPreambleLength(long length) {
+void sx128x::setPreambleLength(long length)
+{
_preambleLength = length;
setPacketParams(length, _implicitHeaderMode, _payloadLength, _crcMode);
}
// not implemented
}
-void sx128x::enableCrc()
-{
+void sx128x::enableCrc() {
_crcMode = 0x20;
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
}
-void sx128x::disableCrc()
-{
+void sx128x::disableCrc() {
_crcMode = 0;
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
}
-byte sx128x::random()
-{
+uint8_t sx128x::random() {
// todo: implement
+ return 0x4; //chosen by fair die roll
+ //guarenteed to be random
+ //https://xkcd.com/221/
}
void sx128x::setSPIFrequency(uint32_t frequency)
setPacketParams(_preambleLength, _implicitHeaderMode, _payloadLength, _crcMode);
}
-void sx128x::clearIRQStatus() {
- uint8_t buf[2];
-
- buf[0] = 0x00;
- buf[1] = 0x00;
-
- executeOpcodeRead(OP_GET_IRQ_STATUS_8X, buf, 2);
-
- executeOpcode(OP_CLEAR_IRQ_STATUS_8X, buf, 2);
-}
-
sx128x sx128x_modem;
\ No newline at end of file
projects / lora-radio.git / commitdiff